PirateBox DIY – OpenWrt
Update May 30, 2014!
PirateBox 1.0 has been released and building or upgrading a PirateBox has never been easier! Please refer to this tutorial for instructions and more info. For support, be sure to visit the new PirateBox Forum.
Outdated Instructions Below!
Stuff You’ll Need
- TP-Link MR3020 (Newegg) or TP-Link TL-WR703N (DX) (eBay)
- USB Flash Drive (formatted FAT32 with a single partition)
- Ethernet cable
- 5V/USB Battery (optional)
The following tutorial was created on a Mac running OSX 10.8. However, these instructions will also work for Linux or Windows (requires PuTTY).
1. First download a custom copy of OpenWrt for the MR3020 (modified by Matthias Strubel to include all needed kernel-modules). See this thread on the forum for more info. NOTE: The 12.09 OpenWrt firmware has been reported to not work! See see this OpenWrt discussion thread before proceeding. For the WR703N, download this OpenWrt firmware
2. Set the toggle switch located beside the LAN/WAN port to WISP mode
3. Turn off your laptop’s wireless (in OSX, click on the wifi icon and select “Turn Wi-Fi Off”)
5. Enter the default username & password (admin & admin)
6. Navigate to System Tools > Firmware Upgrade and select the OpenWRT firmware
(Note: The WR703N firmware text is in Chinese. To flash OpenWrt from the web interface, select the last menu item on the left, and then the third submenu item. More info in this Village Telco post).
7. After the upgrade completes, the system will restart
8. Telnet to the device:
9. Use the passwd command to set your login password – this will enable SSH:
10. Edit the network file with vi (vi cheat sheet):
NOTE: The following instructions assume your gateway router’s (home router’s) IP address is 192.168.2.1. If your gateway router differs from this, you will need to modify your network file accordingly. Keep in mind that your OpenWrt (PirateBox) router should not have the same address as your gateway router though it will need to be on the same subnet in order to access and download files from the Internet.
The modified file should look like this:
config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option ifname 'eth0' option type 'bridge' option proto 'static' option ipaddr '192.168.2.111' option netmask '255.255.255.0' option gateway '192.168.2.1' list dns '192.168.2.1' list dns '22.214.171.124'
11. Remove the power from the router.
12. Turn ON your laptop’s wireless (for OSX, click on the wifi icon and select “Turn Wi-Fi On”)
13. Connect the MR3020 (or WR703N) to your gateway router (e.g. your home network router) with an ethernet cable and plug the power back in. Wait a couple of minutes until the router boots up. With your computer connected to your home network, try sshing into the router (Note: use the “ipaddr” you assigned in step 9):
14. Ping google to ensure your firewall settings are correct:
15. Add USB support to OpenWrt by installing and enabling the following packages (Note: this step is not required if you used the customized OpenWrt image from step 1):
opkg update opkg install kmod-usb-uhci insmod usbcore ## may return: file exists insmod uhci opkg install kmod-usb-ohci ## may return: up to date. insmod usb-ohci
Next you’ll need to install PirateBox on the router.
1. Connect your USB drive (formatted to FAT32 with only one partition) to the USB port.
2. Install the mkPirateBox package by issuing the following commands.
cd /tmp opkg update && opkg install http://piratebox.aod-rpg.de/
3. Optional: Install the Kareha Image Board:
conf install /opt/piratebox/bin/install_ piratebox.sh /opt/piratebox/conf/piratebox. conf imageboard
Afterwards, edit the Kareha image board config file to change the admin username and password (ADMIN_PASS and SECRET):
4. Once the install is completed, unplug the ethernet cable and disconnect the power for at least 10 seconds.
5. Restart the device and join the “PirateBox – Share Freely” network. Open any web page and you should be redirected to the PirateBox menu.
6. Begin sharing files and chatting!
To upgrade from an earlier version of PirateBox, check out this tutorial on the PirateBox forum.
More info about building a serial port (useful for recovering a “bricked” router) for the TL-WR703N on TheVillageTelco wiki.
Please post your questions, discoveries, ideas, and solutions in the PirateBox Forum.